Free Estimates in Rhode Island and Massachusetts Find Your Town (401) 593-3983
RTP HVACA Rooftop Power Company

Home / Blog / Boiler Pressure Dropping or Radiators Not Heating: What to Check

Boiler Pressure Dropping or Radiators Not Heating: What to Check

Boiler pressure dropping or radiators staying cold? Learn what the gauge should read, the safe checks to make, and what to leave to a technician.

By RTP HVACPublished 5 Min Read

Free, No-Obligation Estimates Manual J Load Calculations Help With Rhode Island Rebate Programs Based in Warwick, RI

The radiators are lukewarm or cold, the boiler is running, and when you look at the gauge the needle is sitting near zero. Or the pressure was fine last week and keeps creeping down. Both can mean the system is short of water or has air trapped in it, and there are other causes. This post covers what the gauge should read, the checks that are safe for a homeowner, and where to stop. If you smell gas, hear a hiss or a carbon monoxide alarm sounds, get everyone out of the house and call 911 from outside before you read further.

It applies to hot water systems, the kind that circulate heated water through radiators or baseboard. Some older Rhode Island homes have steam radiators instead. Steam systems behave differently and a hot steam radiator can release scalding steam, so if you are not sure which you have, skip the troubleshooting and call.

What the Gauge Should Read

Boiler manufacturers' manuals commonly call for filling a residential hot water system to about 12 psi when cold, and many boilers have a maximum working pressure of 30 psi, with some rated for 50 psi.

Those are typical numbers, not yours. Read the label and the manual for your boiler. Check the gauge when the system is cold. If it reads near zero or below the minimum in your manual, turn the boiler off at its switch and call a technician rather than running it for a hot reading. If the cold reading looks normal, check it again when the system is running hot, and write both numbers down. If it falls near zero, turn the boiler off and call. A gauge can stick or read wrong, so if a reading looks off, ask a technician to confirm it.

Safe Checks Before You Call

Start with the simple things.

  1. Confirm the boiler has power. Look for a lit switch or display and look at the emergency switch near the boiler. If it is off, leave it off and call.
  2. Read the pressure gauge, cold if you can. If it reads near zero or below the minimum in your manual at any time, turn the boiler off at its switch, stop here and call.
  3. Check the thermostat. Make sure it is set to Heat, set above room temperature, and has working batteries if it takes them.
  4. If you heat with oil, look at the tank gauge. An empty tank looks exactly like a failed boiler.
  5. Look, without touching, for water around the boiler, on the floor, along the visible pipes and at radiator valves. Rust staining or damp patches suggest a slow leak.
  6. Once the system is running, note which radiators heat up and which stay cold. A working radiator can be hot enough to burn, so hold a hand near the surface rather than on it.

If you find a puddle, a reading at or above the maximum on the boiler's label (often 30 psi), or a relief valve that is spitting water, turn the boiler off at its switch and call. Do not open or adjust the relief valve, and never cap or plug it.

Radiators Cold at the Top

A radiator that is warm at the bottom and cold at the top usually has air in it. Air rises, and a pocket at the top keeps hot water from filling the radiator. Letting the air out through the small bleed valve is a job many homeowners do, and the basic steps are:

  • Turn the boiler off and let the radiators cool.
  • Hold a cup or rag under the bleed valve and open it slowly with a radiator key. Hot water can scald, so make sure the radiator has cooled.
  • Close it as soon as a steady stream of water comes out with no air.
  • Many guides suggest starting on the lowest floor and working up. Then check the boiler gauge.

Bleeding fixes trapped air, but it also releases water, so the pressure can drop. If the gauge then reads low, leave the boiler off and call a technician, who should repressurize the boiler and find why it lost pressure.

Do not force a stuck bleed valve. Steam radiators are not bled this way at all.

When Pressure Keeps Dropping

Once air is out and a technician has restored the pressure, it should generally hold. If the gauge keeps drifting down, or radiators keep needing to be bled, something may be letting water out or air in. A technician will usually look at:

  • Leaks in pipes, valves and radiators.
  • The automatic fill valve, which sets the cold pressure.
  • The expansion tank. A failed tank can cause abnormally high pressure when the boiler heats up, and pressure above the relief valve rating can open the valve.
  • Air getting into the system.

Each of those involves parts under pressure or hot water, and the fix is not a homeowner's job. See our page on boiler repair and replacement for the signs and options it covers.

What Not to Do

  • Do not keep topping up the water every few days. Repeated refills hide a leak or a fill problem instead of solving it.
  • Do not turn the thermostat way up to compensate. A boiler that is short of water or full of air will not heat faster.
  • Do not remove the boiler cover, touch the burner, the gas valve or the wiring, or work on the expansion tank.
  • Do not bleed or open fittings on a hot steam radiator.

Smells and Alarms Come First

If you smell gas or hear a hiss near the boiler, get everyone out of the house right away and call 911 or the gas utility from outside. Do not flip switches or use a phone inside. If a carbon monoxide alarm sounds, get everyone outside and call 911. Do not try to troubleshoot first.

An Old Boiler That Keeps Needing Attention

ENERGY STAR lists a furnace or boiler more than 15 years old as one sign it may be time to compare replacement, along with frequent repairs and rising energy bills. Age alone does not decide it. When you call, have the gauge numbers, which radiators are cold and what you have already tried, so the visit starts at the right place. Our heating page covers the options, and the rebates page lists programs and sources to check, since incentives change.

Frequently Asked Questions

What should boiler pressure be?

Many boiler manuals call for filling a residential hot water system to about 12 psi when cold, and many boilers have a maximum working pressure of 30 psi. The boiler's label and manual give the correct range for your system.

Why does my boiler keep losing pressure?

Common causes include a leak somewhere in the piping, radiators or valves, a problem with the automatic fill valve, or air getting into the system. Bleeding a radiator also lets some water out, which can lower the reading. If pressure keeps falling, a technician should find the cause.

Why are my radiators cold at the top?

Air rises to the high points of a hot water system, and a pocket of air at the top of a radiator can stop hot water from filling it. The top stays cold while the bottom warms. Bleeding releases the air but also some water, so the boiler pressure needs a recheck afterward.

Is it safe to add water to my boiler myself?

No. If the gauge reads low, a technician should repressurize the boiler and find why it lost pressure. Overfilling can make the relief valve discharge.

What does it mean if the relief valve is dripping?

Boiler pressure above the relief valve rating, often 30 psi, can open the relief valve, and a discharging valve usually means something is wrong with the pressure, the expansion tank or the fill setting. Turn the boiler off and call a technician. Never cap or plug the valve.

Back to Blog

Boiler Pressure Keeps Dropping?

Write down the gauge reading, then call RTP HVAC at (401) 593-3983 and tell us what the radiators are doing.

Free EstimateFind Your Town